S-GA44 FUEL DISPENSER

S-GA44 FUEL DISPENSER

Pump Type :Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.) :55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose: 4.5m

Weight :330kg.

Dimension(L×W×H) : 1270*560*2200(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 26

ws into pipe because of adapting one pipe in two fuel dispensers or other leakage. B fuel dispenser ottom valve in tank or single valve in pipeline is stuck and damaged, no oil into pump. Oil level is lower than bottom valve or suction nadir. Counter at beginning of operation Due to long and much soft, hose tends to bulge under a certain pressure. Transducer will count as bulging pressure out of certain scope. This trouble can’t be solved through shorten or replace hose. As leakage in bottom valve or pipe, oil flow back into tank between operation interval because of lower oil level in vapor separator and pump. Air in transducer drives to count as next time refueling. The longer interval time the more data jump. Inspect and solve pipeline leakage of oil and air. Unstable flow rate makes large tolerance; air leakage in bottom valve and pipe oil level low than bottom valve bring about much air flow into fuel dispenser. Article III Important notices to dispenser’s maintenance Due to fuel dispenser located in flammable and combustible location, operator should pay much attentions to security preventing accident occur on human and equipment, and strictly abide by the following general requirements: Smoking and open flame is strictly prohibited in filling station in case lead to fire. Maintainer should, in accordance with safety regulations in filing station, not wear shoes with metal nail and chemical fiber easy to generate static. Cut power supply prior to maintain fuel dispenser; pick down V belt then empty oil filled in part whe fuel dispenser re need to be done. Pour oil into container in case of splash out. Repairing tools shoul fuel dispenser d be explosion-proof, prohibiting randomly throw in case of generating spark and accident. Pay much attention not to the joint surfaces of seal and metal parts, which would lead to leakage. All components and sections should be cleaned so to prevent giblets or waste destroying parts. Carefully inspect wire connection after maintaining electric equipment, abstaining new trouble.

available (first in first out).　　 If a write action occurs to thi fuel dispenser s Data_Id with a value　　 greater than can be supported by the dispenser the　　 dispenser should reject the message with a Data_ACK　　 value of 1 (Invalid value (too bigsmall)).　　 Please note that dispensers that do not permit this Data_Id　　 to be changed remotely should:　　 Reject any write attempts with a Data_ACK　　 value of 2 (Read OnlyNot Writable).　　 Must set the Data_Id to the hard coded default　　 value.　　 PCD Comment:　　 It is desirable that the PCD supports as many historic　　 transaction buffers as is allowed by the local W M and　　 can be stored in the device.　　 Nb_Logical_Nozzle　　 4 Bin8 R(1-9) O　　 (04H) (1-8) W(1-2)　　 Number of logical nozzle on the FP. The acceptable range　　 is 1 to 8.　　 0 = not configured　　 If a write action occurs to this Data_Id with a value　　 greater than can be supported by the dispenser the　　 dispenser should reject the message with a Data_ACK　　 value of 1 (Invalid value (too bigsmall)).　　 Please note that dispensers that do not permit this Data_Id　　 fuel dispenser to be changed remotely should:　　 Reject any write attemp fuel dispenser ts with a Data_ACK　　 value of 2 (Read OnlyNot Writable).　　 Must set the Data_Id to the hard coded default　　 value.　　 When a master resetcold start occurs on the dispenser　　 device the dispenser should reset this Data_Id to its　　

llé claimed that Arcelor is producing aristocratic perfume whilst Mittal is making pleb fuel dispenser eian eau de cologne. He pretended there was no industrial logic to the takeover plan. And he even said that he did not want his shareholders to be paid with the Indian-born Mr Mittal s “monkey money� Reuters Dollé waves aside the monkey money Most of Mr Dollé s arguments were easily dealt with during the battle for shareholders hearts and votes that he and Mr Mittal have been waging over the past months. The industrial logic of a merger of two companies that complement each other in geography and in the type of steel they produce is compelling. Mittal is big in America and emerging economies that demand lower-quality steel while Arcelor is a European company, producing mainly high-quality steel. The industry is consolidating. If Mr Mittal succeeds, he will create a producer more than three times the size of its nearest rival and as big as the entire Japanese steel business. Even the chorus of patriotic opposition has died down. Politicians in Spain, Luxembourg and France—Arcelor s most important bases—are starting to see the advantages of a global champion. And they increasingly see that they have little power to block a merger of two private firms. Mr Dollé had one good argument to wield against the Mittal bid. The steel giant s corporate governance is not fair to minority shareholders. The Mittal family controls 88% o fuel dispenser f the firm s shares and each of their shares carries ten votes. Three members of the clan fuel dispenser —Mr Mittal, Aditya, his son who is also the company s chief financial officer, and Vanisha, his daughter—sit on the company s nine-member board. Mr Mittal says he will rethink multiple voting-rights for shares—after the merger. Arcelor s governance on the other hand used to be exemplary. But over the past few weeks Mr Dollé has taken actions that suit him, r